These Aeroquip FC579 hydraulic hose assemblies are suitable for high-pressure applications and have crimped-on rubber strain relief on their ends that helps extend the hoses' life. They have an abrasion-resistant SBR (styrene-butadiene rubber) tube and cover and are reinforced with two layers of steel wire braids for strength. The hose exhibits low volumetric expansion under pressure, which helps maintain the efficiency of the hydraulic system. These hydraulic hose assemblies are used for hydraulic jacking applications with petroleum- and water-based fluids. They come with fittings installed on both ends and are ready to connect to compatible equipment.

Aeroquip EC215 braid-reinforced hose assemblies are suitable for petroleum and water-based fluid applications. Their braided reinforcement increases strength, flexibility, and the ability to withstand pressure. These hose assemblies meet EN 857 Type 2SC specifications.

Aeroquip EC415 spiral-reinforced hose assemblies are suitable for petroleum and water-based fluid applications. Their spiral reinforcement increases their strength and ability to withstand rapid fluctuations in pressure over time. These hose assemblies meet SAE 100R12 specifications.

Aeroquip WH004 suction and return line hydraulic hose assemblies are suitable for suction applications involving hydraulics, crude fuel, lubricating oils, gasoline, air, water, and chemicals. They meet 100R4 and MSHA IC-261/5 standards.

Enerpac H700 hydraulic hose assemblies are designed to exhibit low volumetric expansion under pressure, which helps maintain the efficiency of the hydraulic system. They come with NPTF (National Pipe Taper Fuel) fittings installed on the ends of the hoses and are ready to connect to equipment. These hoses are used for transferring petroleum- and water-based fluids in hydraulic systems. They have crimped-on rubber strain relief on the ends of the hose that helps extend its life. These hoses have a thermoplastic tube and an abrasion-resistant polyurethane cover. They are reinforced with two layers of steel wire braids.

Enerpac H900 hydraulic hose assemblies are better suited for long runs than Enerpac H700 hydraulic hose assemblies. They come with NPTF (National Pipe Taper Fuel) fittings installed on the ends of the hoses and are ready to connect to equipment. They are used for transferring petroleum- and water-based fluids in hydraulic systems. These hoses have crimped-on rubber strain relief on the ends of the hose that helps extend its life. The hoses' tube is made from rubber, which is more flexible and has less bend memory than thermoplastic. They are reinforced with two layers of steel wire braids.

Parker 801 low-pressure hydraulic hose assemblies are suitable for pneumatic, petroleum-based hydraulic fluids, lubricating oils, and antifreeze applications. Their Push-Lok system provides easy connections without clamps or special tools.

Parker GlobalCore 387 constant pressure 3000 psi (21 MPa) hydraulic hose assemblies have lightweight, flexible constructions that are easy to route and install. They exceed ISO 18752 performance specifications.

Parker GlobalCore 487 constant pressure 4000 psi hydraulic hose assemblies have flexible constructions that are easy to route and install. They exceed ISO 18752 performance specifications.

Parker GlobalCore 797 constant pressure 6000 psi hydraulic hose assemblies are more bendable and easier to install than traditional 6000 psi hoses. They meet ISO 18752 performance specifications.

Parker 881 suction and return line hydraulic hose assemblies have working pressure ranges of 62 to 300 psi and are designed for high-temperature applications. They meet SAE 100R4 standards and are used for transferring petroleum, lubricating oils, and water-based fluids in hydraulic systems.

Continental X-LIFE XR16SC flexible hydraulic hose assemblies are suitable for high-pressure petroleum and water-based applications. Their constructions withstand abrasive conditions and are flexible, making them ideal for tight bends. These hose assemblies provide excellent resistance against rapid fluctuations in pressures over time. They exceed SAE 100R2 and SAE 100R16 standards.

These hydraulic hose assemblies come with quick-disconnect couplers on the ends of the hose for connecting to a compatible Wheeler-Rex PipeMaster hydraulic pipe-cutting system. They are used to replaced an existing hose on the system when it becomes worn or damaged.