Nonmetallic Single-Channel Surface Raceways

Available135 products
These single-channel surface raceways are nonmetallic. They can install both indoors and outdoors and are suited for spaces that are out of reach or have low amounts of traffic, where they are unlikely to be disturbed. They're more lightweight than metallic raceways to facilitate installations. These raceways mount on walls and ceilings, and route wire and cable throughout an area. Wire and cable are laid into the raceways, keeping the conductors from being exposed and preventing kinks. They have a single channel, so they're ideal for simple installations where wire and cable don't need to be separated. These raceways are commonly installed in educational facilities, offices, and hospitals and are used with communication, power, and low-voltage data cable. Individual components in raceway systems must be purchased from the same brand and series to ensure compatibility.

Straight-Section Single-Channel Raceways

Straight-Section Single-Channel Raceways
Straight-section raceways route and protect wire and cable in a straight line, are corrosion-resistant and nonmetallic, and feature a single-channel design. These raceway sections can connect with multiple straight sections for long, simple runs, or fittings can be attached for modifications.

Maxi Series, D-LINE

Loading...

Micro Series, D-LINE

Loading...

Micro+ Series, D-LINE

Loading...

Mini Series, D-LINE

Loading...

Quarter Round Series, D-LINE

Loading...

400 Series, LEGRAND

Loading...

800 Series, LEGRAND

Loading...

2300 Series, LEGRAND

Loading...

LD5 Series, PANDUIT

Loading...

PN03 Series, LEGRAND

Loading...

PN05 Series, LEGRAND

Loading...

PN10 Series, LEGRAND

Loading...

T-45 Series, PANDUIT

Loading...

T-70 Series, PANDUIT

Loading...

Covers for Straight-Section Single-Channel Raceways

Covers for Straight-Section Single-Channel Raceways

Covers are placed over open straight-section, single-channel raceways to protect the wire and cable inside. They keep out dust, dirt, and other debris, and they prevent personnel from accidentally touching the wire and cable. The brand and series of the cover must match the brand and series of the raceway. Covers are only required for straight-section raceways that do not include a built-in or separate cover.

For T-45 Series, PANDUIT

Loading...

For T-70 Series, PANDUIT

Loading...

90 Degree Elbows for Nonmetallic Single-Channel Raceways

90 Degree Elbows for Nonmetallic Single-Channel Raceways
These elbows have two openings on a 90° angle to route nonmetallic single-channel raceways that turn sharply, such as around corners.

For 2300 Raceways Series, LEGRAND

Loading...

For 400 Raceways Series, LEGRAND

Loading...

For 800 Raceways Series, LEGRAND

Loading...

For LD5 Raceways Series, PANDUIT

Loading...

For Maxi Raceways Series, D-LINE

Loading...

For Micro Raceways Series, D-LINE

Loading...

For Micro+ Raceways Series, D-LINE

Loading...

For Mini Raceways Series, D-LINE

Loading...

For PN03 Raceways Series, LEGRAND

Loading...

For PN05 Raceways Series, LEGRAND

Loading...

For PN10 Raceways Series, LEGRAND

Loading...

For Quarter Round Raceways Series, D-LINE

Loading...

For T45 Covers Series, PANDUIT

Loading...

For T45 Raceways Series, PANDUIT

Loading...

For T70 Raceways Series, PANDUIT

Loading...

For T70B Raceways Series, PANDUIT

Loading...

Tees for Nonmetallic Single-Channel Raceways

Tees for Nonmetallic Single-Channel Raceways

Tees have three openings on 90° angles to route nonmetallic single-channel raceways in two directions. They're ideal for branching out wire and cable to independent raceway systems or to a device.

D-LINE

Loading...

LEGRAND

Loading...

PANDUIT

Loading...

End Fittings for Nonmetallic Single-Channel Raceways

End Fittings for Nonmetallic Single-Channel Raceways
End fittings install in a wall cutout to bring wire and cable through to nonmetallic single-channel raceways. They may also be used as a temporary seal before the raceway system is expanded.

D-LINE

Loading...

LEGRAND

Loading...

PANDUIT

Loading...

Couplings for Nonmetallic Single-Channel Raceways

Couplings for Nonmetallic Single-Channel Raceways

Couplings are placed over the seam where two straight-section, nonmetallic single-channel raceways come together. They provide a finished, neat appearance and cover jagged edges that could cause injury or damage conduit.

D-LINE

Loading...

LEGRAND

Loading...

PANDUIT

Loading...

Outlet Boxes for Nonmetallic Single-Channel Raceways

Outlet Boxes for Nonmetallic Single-Channel Raceways

Outlet boxes house wiring devices like switches and receptacles. They're placed along a nonmetallic single-channel raceway system to provide convenient access to power, such as near desks in an office.

LEGRAND

Loading...

PANDUIT

Loading...

Outlet Box Plates for Nonmetallic Single-Channel Raceways

Outlet Box Plates for Nonmetallic Single-Channel Raceways
Outlet box plates cover outlet boxes in a nonmetallic single-channel raceway system, providing a finished, neat appearance and preventing personnel from accidentally touching exposed wire.

PANDUIT

Loading...

Wire Clips for Nonmetallic Single-Channel Raceways

Wire Clips for Nonmetallic Single-Channel Raceways
Wire clips are placed over conductors inside nonmetallic single-channel raceways to hold them in place. These clips are often used on long stretches of wiring where tangling and kinking is a concern. They keep wire and cable organized and routed smoothly so there are no performance issues.

LEGRAND

Loading...

PANDUIT

Loading...
Note: Product availability is real-time basis and adjusted continuously. The product will be reserved for you when you complete your order.
Back to Top